- Is Grade 8 or 10.9 stronger?
- Are stainless bolts stronger than Grade 8?
- What is the difference between 8.8 and 12.9 grade bolts?
- Is a 12.9 Bolt stronger than Grade 8?
- How much weight will a 5/16 bolt hold?
- What grade of bolts are the strongest?
- What is the shear strength of a Grade 5 bolt?
- What is stronger Grade 5 or Grade 8 bolts?
- Will Grade 8 bolts rust?
- How can you tell if a bolt is high tensile?
- Are higher grade bolts more brittle?
- What is the difference between a 10.9 and 12.9 Bolt?
- What is the strength of a grade 5 bolt?
- Do carriage bolts have shear strength?
- What is a 12.9 grade bolts?
- Is there a grade 10 bolt?
- What is the metric equivalent to Grade 8?

## Is Grade 8 or 10.9 stronger?

Class 10.9 is stronger than class 8.8.

It is commonly found in high strength automotive applications.

Class 10.9 is similar to grade 8.

A low carbon steel for general use..

## Are stainless bolts stronger than Grade 8?

Stainless steel bolts are rated for corrosion resistance. Bolt strength is rated in PSI (pounds per square inch). A stainless steel bolt has the same PSI rating as a grade 5 bolt (125,000 PSI). A grade 8 bolt has a stronger rating with a PSI of 150,000.

## What is the difference between 8.8 and 12.9 grade bolts?

The mechanical difference between the 12.9 and 8.8 is yield strength (roughly 90% of 1200 MPa vs 80% of 800 MPa). That means the 12.9 can be stretched further (i.e. torqued to some higher value) before it yields, which of course increases the clamp force.

## Is a 12.9 Bolt stronger than Grade 8?

Many fasteners (screws, etc.), especially smaller sizes, are typically not graded—their strength isn’t specified….Table 1.Grade/ClassStrengthMetric Class 8.8Similar to Grade 5.Metric Class 10.9Similar to Grade 8.Metric Class 12.9The highest metric class for strength, it exceeds Grade 8.11 more rows

## How much weight will a 5/16 bolt hold?

If a lag screw with a 5/16-inch shaft is installed correctly, it can withstand pull-out, or withdrawal, of up to 212 pounds in close-grain hem, fir and redwood, and up to 266 pounds in larch Douglas fir, according to information from the American Wood Council.

## What grade of bolts are the strongest?

grade 8The strongest commercial-quality bolt is grade 8, marked by six raised dashes; its medium-carbon alloy steel has been quenched and tempered to achieve a tensile strength of 150,000 psi.

## What is the shear strength of a Grade 5 bolt?

For example, an SAE grade 5 hex cap screw has a specified minimum tensile strength of 120,000 psi. Therefore, for design purposes, its shear strength could be reasonably assumed to be 70,000 psi.”

## What is stronger Grade 5 or Grade 8 bolts?

Grade 8 bolts have been hardened more than grade 5 bolts. Thus they are stronger and are used in demanding applications such as automotive suspensions. Grade 8 bolts have 6 evenly spaced radial lines on the head. Grade G is roughly equivalent to Grade 8.

## Will Grade 8 bolts rust?

Grade 8 bolts have 6 evenly spaced radial lines on the head.” Unlike stainless steel, which is highly resistant to corrosion, steel, however reinforced, will oxidize over time and rust. Grade 8 bolts that are not galvanized or plated with yellow zinc, however, are cheaper.

## How can you tell if a bolt is high tensile?

To identify this grade, look out for an ‘8.8’ stamp or a set of three radial lines on the head of the bolt. Most often, customers looking for a high tensile bolt may just be looking for the 8.8 grade.

## Are higher grade bolts more brittle?

One common misconception about bolts is that a higher rated bolt is stronger, yet more brittle, and therefore lower grades should be used in places like in suspension systems so they can deform rather then break. This is wrong! There are two types of forces a bolt experiences, tension and shear.

## What is the difference between a 10.9 and 12.9 Bolt?

12.9 grade steel has 120% of the tensile strength of 10.9 grade steel. The “12” prefix indicates a tensile strength of X100 N/mm^2 and the “9” suffix indicates a multiplier. Both 12.9 and 10.9 have the same multiplier, so the comparison is straightforward: 12 to 10.

## What is the strength of a grade 5 bolt?

Bolt Grade Markings and Strength ChartHead MarkingGrade and MaterialMechanical PropertiesMin. Tensile Strength (psi)3 Radial LinesGrade 5 Medium carbon steel, quenched and tempered120,000105,0006 Radial LinesGrade 8 Medium carbon alloy steel, quenched and tempered150,00018 more rows

## Do carriage bolts have shear strength?

Carriage bolts are designed to be tightened from the nut side of the assembly. … Grade 8 carriage bolts have 6 radial lines on the head, its a medium carbon alloy steel, quenched and tempered. They have a tensile strength of 150,000 psi and a shear strength of 90,000 psi.

## What is a 12.9 grade bolts?

The minimum ultimate tensile strength of the Grade 12.9 Metric Hex Head Bolts is about 1242 Mpa or 180,000 PSI, making them the highest grade of bolts produced.In fact, the Grade 12.9 Nuts is known for their high tensile strength.

## Is there a grade 10 bolt?

Class 10. This is a metric nut grading similar to the SAE grade 8 classification, which is used in conjunction with Class 10.9 bolts. This strength of nut is used in automotive, and structural industries, as well as in high temp applications.

## What is the metric equivalent to Grade 8?

Approximate Equivalency Chart Metric/US Roughly Equivalent US Bolt MaterialsMetric Nut ClassSAE J429Normally UsedGrades8.8859.895+10.910or 12812.910or 12.3 more rows